• Questions?
  • 772-742-8535
  • orderdesk@boatbuildercentral.com
  • CONTACT US
  • About Us
  • Builder’s Forum
  • Support & Tutorials
    • Tutorials
    • Plan Updates
    • FAQ
    • Photo Gallery
  • Products
    • Hardware
      • Jackplates
      • Trim Tabs
      • Fuel System
      • Deck Hardware
      • Custom Built Accessories
      • Rubrail and Extrusion
      • Thru-hull / Plumbing
      • Electrical
    • Paint & Primer
      • Awlgrip
      • Interlux
      • Pettit
      • Engineered Marine Coatings
      • System Three Paint
      • Varnish
      • Bottom Paint
    • Epoxy
      • MarinEpoxy
      • System Three Epoxy
      • West System
      • Clear Coat / Tabletop
      • Epoxy Pigments
      • Repair / Trial kits
      • Resin Calculator
      • Metric Resin Calculator
    • Tools
      • Abrasives
      • Application
      • Safety gear
      • Measure and mix
    • Fiberglass
      • Fiberglass Tape
      • Biaxial Cloth
      • Woven Fabric
      • Carbon / kevlar
      • Xynole Cloth
    • Core Materials
      • Foam Core
      • Transom Foam
      • Honey Comb
      • Composite Parts
    • Glues & Adhesives
      • Sealants
      • Adhesives
      • Epoxy Glue
    • Fillers & Fairing
    • Buoyancy Foam
    • Polyester/Gelcoat
    • Product Search
  • Marine Plywood
    • BS-1088 Okoume
    • BS-1088 Meranti
    • BS-6566 Meranti
    • Product Search
  • Plans & Kits
    • Popular Fishing Boats
    • Power Boats
      • Power Boats Under 16’
      • Power Boats 17’ – 21’
      • Power Boats Above 21’
    • Sailboats
      • Day Sailers
      • Sailboats less than 21’
      • Sailboats above 21’
    • Canoes, Kayaks, and Dinghies
    • Multi-Hulls
      • Beach Cats
      • Power Cats
      • Sail Cats (20-25′)
      • Pontoon Type
      • Trimarans
    • Optimist Club Racer
    • Consoles & Pilothouses
    • Specialty Designs
    • Product Search
  •  
  •  
  • Products
    • Hardware
    • Paint & Primer
    • Epoxy
    • Tools
    • Fiberglass
    • Core Materials
    • Glues & Adhesives
    • Fillers & Fairing
    • Buoyancy Foam
    • Polyester/Gelcoat
    • Product Search
  • Marine Plywood
    • BS-1088 Okoume
    • BS-1088 Meranti
    • BS-6566 Meranti
    • Product Search
  • Plans & Kits
    • Popular Fishing Boats
    • Power Boats
    • Sailboats
    • Canoes, Kayaks, and Dinghies
    • Multi-Hulls
    • Optimist Club Racer
    • Consoles & Pilothouses
    • Specialty Designs
    • Product Search
  •  
  •  
optimist-club-racer
MENUMENU
  • Club Racer Kits
    • Club Racer Epoxy/Fiberglass Kit
    • Club Racer CNC Hull Kit
    • Club Racer Complete Kit
    • Club Racer Basket Mold Kit
  • Building the Racer
    • Study Plans
    • Kit Building Notes
    • Mold Building Notes
    • Forum Building Thread
    • Building Gallery
We're really sorry...
Close
...we don't currently have that one in stock
Please add your email and we'll notify you when it's back
Home » Hardware » Jackplates
Convertable MJ5 2.5″ or 5″ setback manual jack plate :200 HP MAX

Convertable MJ5 2.5″ or 5″ setback manual jack plate :200 HP MAX

Price: $259.95
Quantity:
-
+
  Product ID BMS_MJ5_convertible
  ISBN 100-205000
  Updated
06/25/2015
  •    Info
2 1/2 inch offset no wedge A feature which is used on the lightest of boats. Allowing the engine to be raised to its maximum height without putting the weight of the engine too far behind the transom which could create too much bow lift.
We used this jack plate on our FS17 skiff and we love it, adjustable with only a wrench, it allows for a nice offset and for easy "dialing" in of your engine height. See below link to the gallery of this boat



2 1/2 inch Offset with Negative 6-Degree Wedge This design can be used when the transom of a boat is too steep of an angle to allow the outboard motor to perform properly. For example: an 18-degree transom when this design is applied.

5-inch Offset No Wedge This option desirability will vary from one boat to another depending upon weight and length of boat. Some outboard motors have a limited trim angle and the 6-degree wedge may not allow for enough bow lift. By setting the plate at the no wedge design, it will give maximum bow lift.

5-inch Offset with 6-Degree Wedge

* Jacking bolts- allow motor to be moved to any height. No need to take boat out of the water.
* Offset- positions motor 5 1/2 inches behind transom. This allows prop to run in cleaner water, away from the turbulence and bubbles created by the hull. This helps stop slippage of prop, and helps stop torque in steering wheel at high speeds.
* Trim-In- this allows motor to be trimmed in or down 6 degrees more than if mounted flat on transom. Helps stop low speed porpoising. Balance load better.
* Light-weight- approximately 20lbs., constructed of aircraft grade aluminum and stainless steel.
* Anodized- anodized black finish to prevent corrosion. Anodize also lets paint stick to aluminum if painting is preferred.
* Narrow designed- only inches wide, make this plate possible to fit the narrowest of transoms.
* Fits V-6- pre-drilled to fit all late model V-6's. Can be modified to fit any size outboard.
Converting the new 4 in 1 is as easy as dropping anchor!
Adjustable plates turn 180 degrees and switch sides, then bolt in place.
« Previous | Next »
Tweet
© 2019 Boat Builder Central. All Rights Reserved.